BV10S
BV10S
Light vinylester bonding paste slow
BV10 series bonders are certified by RINA (Type Approval DIP146622CS)
Adhesive bonding paste based on unsaturated vinylester resins, microspheres and light reinforcing fillers, characterized by a specific formulation for long gel time, high mechanical properties and low shrinkage.
Specifically formulated for the use of large vacuum bags and for bonding sheets and inserts in Balsa, PVC, PET, PIR and polyurethane foam, is easily spatulable and deaerable without dripping from vertical surfaces. Under pressure or vacuum it flows easily, saturating every crack and cavity of the foam thus ensuring high mechanical, thermal and chemical properties to the sandwich laminate. The low specific weight of its formulation is combined with limited shrinkage during hardening and excellent adhesion performance even on high density foams.
SUPPORTS
Properly prepared and cleaned polyester and vinylester fiberglass laminates.
GENERAL INSTRUCTIONS FOR USE
Product particularly suitable for applications in the summer months. Can be applied directly on freshly laminated surfaces free of dust, fibers, dirt and condensation. Completely hardened surfaces must instead be sanded and cleaned thoroughly. Check the suitability for use on surfaces obtained from paraffin resins. Mix the product directly in its packaging and mix it with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required (See page 8 of “Core Adhesives for Foams guidelines”). The recommended temperature range is between 18 and 28°C. The product contains viracolor in order to verify the homogeneous dispersion of the peroxide. It can be applied manually with a spatula, for quantities over 5 kg, mixing with a whisk is recommended, while for 200 l drums the use of a pressing plate extruder-mixer guarantees the best mixing efficiency. The product has also been formulated to be sprayable, where the large surfaces of components or the rapid cycles of mass production require it. For further details and recommended application procedures, refer directly to the “Core Adhesives for Foams guidelines”, available at the INTEC Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C. Some drift may occur in gel time.
Packaging
kg. 20
kg. 200
Type of use
MOULD-LAMINATION
LAMINATION-ASSEMBLING
See other bonding pastes for core materials
BV10R
BV10R
Light vinylester bonding paste rapid
BV10 series bonders are certified by RINA (Type Approval DIP146622CS)
Adhesive bonding paste based on unsaturated vinylester resins, microspheres and light reinforcing fillers, characterized by high mechanical and thermal properties, and low shrinkage. Specifically formulated for the use of large vacuum bags and for bonding sheets and inserts in Balsa, PVC, PET, PIR and polyurethane foam, is easily spatulable and deaerable without dripping from vertical surfaces. Under pressure or vacuum it flows easily, saturating every crack and cavity of the foam thus ensuring high mechanical, thermal and chemical properties to the sandwich laminate. The low specific weight of its formulation is combined with limited shrinkage during hardening and excellent adhesion performance even on high density foams.
SUPPORTS
Properly prepared and cleaned polyester and vinylester fiberglass laminates.
GENERAL INSTRUCTIONS FOR USE
Product particularly suitable for applications in the winter months. Can be applied directly on freshly laminated surfaces free of dust, fibers, dirt and condensation. Completely hardened surfaces must instead be sanded and cleaned thoroughly. Mix the product directly in its packaging and mix it with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required (See page 8 of “Core Adhesives for Foams guidelines”). The recommended temperature range is between 14 and 18°C. The product contains viracolor in order to verify the homogeneous dispersion of the peroxide. It can be applied manually with a spatula, for quantities over 5 kg, mixing with a whisk is recommended, while for 200 l drums the use of a pressing plate extruder-mixer guarantees the best mixing efficiency. The product has also been formulated to be sprayable, where the large surfaces of components or the rapid cycles of mass production require it. For further details and recommended application procedures, refer directly to the “Core Adhesives for Foams guidelines”, available at the INTEC Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C. Some drift may occur in gel time.
Packaging
kg. 20
kg. 200
Type of use
MOULD-LAMINATION
LAMINATION-ASSEMBLING
See other bonding pastes for core materials
BV10
BV10
Vinylester bonder light
BV10 series bonders are certified by RINA (Type Approval DIP146622CS)
Lightweight adhesive bonding paste based on unsaturated vinylester resins, microspheres and light reinforcing fillers, characterized by high mechanical and thermal properties, and low shrinkage. Specifically formulated for bonding sheets and inserts in Balsa, PVC, PET, PIR and polyurethane foam, is easy to apply, spread with spatula, easily deaerate and stick to the surface without dripping from vertical surfaces. Under pressure or vacuum it flows easily, saturating every crack and cavity of the foam thus ensuring high mechanical, thermal and chemical properties to the sandwich laminate. The low specific weight of its formulation is combined with limited shrinkage during hardening and excellent adhesion performance even on high density foams.
SUPPORTS
Properly prepared and cleaned polyester and vinylester fiberglass laminates.
GENERAL INSTRUCTIONS FOR USE
Can be applied directly on freshly laminated surfaces free of dust, fibers, dirt and condensation. Completely hardened surfaces must instead be sanded and cleaned thoroughly. The suitability for use on surfaces obtained from paraffin resins must be checked. Mix the product directly in its packaging and mix it with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required. The recommended temperature range is between 14 and 28°C. The product contains viracolor in order to verify the homogeneous dispersion of the peroxide. It can be applied manually with a spatula, for quantities over 5 kg, mixing with a whisk is recommended, while for 200 l drums the use of a pressing plate extruder-mixer guarantees the best mixing efficiency.
The product has also been formulated to be sprayable, where the large surfaces of components or the rapid cycles of mass production require it. For further details and recommended application procedures, refer directly to the “Core Adhesives for Foams guidelines”, available at INTEC Technical Assistance Center.
In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C. Some drift may occur in gel time
Packaging
kg. 20
kg. 200
Type of use
MOULD-LAMINATION
LAMINATION-ASSEMBLING
See other bonding pastes for core materials
B10R
B10R
Light polyester bonding paste
Lightweight adhesive bonding paste based on unsaturated polyester resins, microspheres and light reinforcing fibers, characterized by a rapid gel time.
Specifically formulated for the composite sector for bonding core materials and inserts in Balsa, PVC, PET, PIR and polyurethane foam. It is easy to apply, spread with spatula, easily deaerate and stick to the surface thanks to the excellent tixotropy. Under pressure or vacuum it flows easily saturating every crack and cavity of the foam thus ensuring high mechanical, thermal and chemical properties to the sandwich laminate. The low specific weight of its formulation is combined with limited shrinkage during hardening and excellent adhesion performance even on high density foams.
SUPPORTS
Recommended: properly prepared and cleaned polyester and vinylester fiberglass laminates.
GENERAL INSTRUCTIONS FOR USE
The product can be applied directly to freshly laminated surfaces free of dust, fibers, dirt and condensation. Completely hardened surfaces must instead be sanded and cleaned thoroughly. The suitability for use on surfaces obtained from paraffin resins must be checked. Mix the product directly in its package with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required. The recommended temperature range is between 16 and 28°C. The product contains viracolor in order to verify the homogeneous dispersion of the peroxide. It can be applied manually with a spatula or by machine For quantities over 5 kg, mixing with a whisk is recommended. The product has also been formulated to be sprayable, where the large surfaces of components or the rapid cycles of mass production require it. For further details and recommended application procedures, refer directly to the “Core Adhesives for Foams guidelines”, available at INTEC’s Technical Assistance Center.
In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C. Some drift may occur in gel time.
Packaging
kg. 19
kg. 200
Type of use
MOULD-LAMINATION
LAMINATION-ASSEMBLING
See other bonding pastes for core materials
B10
B10
Light polyester bondig paste
Lightweight adhesive bonding paste based on unsaturated polyester resins, microspheres and light reinforcing fillers.
Specifically formulated for the composite sector for bonding core materials and inserts in Balsa, PVC, PET, PIR and polyurethane foam. It is easy to apply, spread with spatula, easily deaerate and stick to the surface thanks to the excellent tixotropy. Under pressure or vacuum it flows easily saturating every crack and cavity of the foam thus ensuring high mechanical, thermal and chemical properties to the sandwich laminate. The low specific weight of its formulation is combined with limited shrinkage during hardening and excellent adhesion performance even on high density foams.
SUPPORTS
Recommended: properly prepared and cleaned polyester and vinylester fiberglass laminates.
GENERAL INSTRUCTIONS FOR USE
The product can be applied directly to freshly laminated surfaces free of dust, fibers, dirt and condensation. Completely hardened surfaces must instead be sanded and cleaned thoroughly. The suitability for use on surfaces obtained from paraffin resins must be checked. Mix the product directly in its package with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required. The recommended temperature range is between 16 and 28°C. The product contains viracolor in order to verify the homogeneous dispersion of the peroxide. It can be applied manually with a spatula or by machine. For quantities over 5 kg, mixing with a stirrer is recommended,
while for 200 l drums, the use of a pressing plate extruder/mixer
guarantees the best mixing efficiency. The product has also been formulated to be sprayable, where the large surfaces of components or the rapid cycles of mass production require it. For further details and recommended application procedures, refer directly to the “Core Adhesives for Foams guidelines”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C. Some drift may occur in gel time.
Packaging
kg. 19
kg. 200
Type of use
MOULD-LAMINATION
LAMINATION-ASSEMBLING
See other bonding pastes for core materials
B07
B07
Bonder poliestere extra leggero
Extra light adhesive bonding paste based on unsaturated polyester resins, microspheres and ultralight reinforcing fillers.
Specifically formulated for the composite sector for bonding core materials and inserts in Balsa, PVC, PET, PIR and polyurethane foam, in constructions that require maximum reduction of weights. It is easy to apply, spread with spatula, easily deaerate and stick to the surface thanks to the excellent tixotropy. Under pressure or vacuum, it flows easily, saturating every crack and cavity of the foam thus ensuring high mechanical, thermal and chemical properties to the sandwich laminate. Characterized by an extra lightweight, it also adds: low shrinkage during hardening and excellent adhesion performance even on high density foams.
SUPPORTS
Recommended: properly prepared and cleaned polyester and vinylester fiberglass laminates.
GENERAL INSTRUCTIONS FOR USE
The product can be applied directly to freshly laminated surfaces free of dust, fibers, dirt and condensation. Completely hardened surfaces must instead be sanded and cleaned thoroughly. The suitability for use on surfaces obtained from paraffin resins must be checked. Mix the product directly in its package with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required. The recommended temperature range is between 16 and 28°C. The product contains viracolor in order to verify the homogeneous dispersion of the peroxide. It can be applied manually with a spatula or by machine. For quantities over 5 kg, mixing with a stirrer is recommended, while for 200 l drums, the use of a pressing plate extruder/mixer guarantees the best mixing efficiency. The product has also been formulated to be sprayable, where the large surfaces of components or the rapid cycles of mass production require it. For further details and recommended application procedures, refer directly to the “Core Adhesives for Foams guidelines”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 8 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C. Some drift may occur in gel time.
Packaging
kg. 13
