G42

G42

Bonding paste smooth without fibres


Adhesive bonding paste viracolor made from unsaturated polyester resins and mineral fibres.
Used in the composite sector for samm angles and chines smoothing, gluing of inserts and core materials.

SUPPORTS

Recommended: Gelcoat, polyester and vinylester fibreglass, wood, various types of foam.

GENERAL INSTRUCTIONS FOR USE

Apply on well sanded and cleaned surfaces;
Make sure the substrate is free of dust, fibres, dirt and surface condensation.
Carefully mix the bonding paste with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required.
The recommended temperature range is between 16 and 28°C. The product contains viracolor.
It must be applied manually with a spatula after careful mixing the hardener or by machine.
For quantities over 5 kg mixing with a stirrer is recommended; for 200 l drums, the use of a pressing plate extruder-mixer guarantees the best mixing efficiency.
In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


Mould - Lamination
Lamination - Assembling

See other bonding pastes



G32

G32

Bonding paste smooth with fibres


Adhesive bonding paste viracolor made from unsaturated polyester resins, reinforced with mineral fibres.
Used in the composite sector for its excellent adhesion in bonding laminates and inserts of various types.
The reinforcing fibers give this product high mechanical resistance, making it suitable for bonding floors and cielings, filling of the strips and gluing inserts.

SUPPORTS

Recommended: polyester and vinylester fibreglass, wood, various types of foam.

GENERAL INSTRUCTIONS FOR USE

Apply on well sanded and cleaned surfaces;
Make sure the substrate is free of dust, fibres, dirt and surface condensation.
Carefully mix the bonding paste with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required.
The recommended temperature range is between 16 and 28°C. The product contains viracolor.
It must be applied manually with a spatula after careful mixing the hardener or by machine.
For quantities over 5 kg mixing with a stirrer is recommended; for 200 l drums, the use of a pressing plate extruder-mixer guarantees the best mixing efficiency.
In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


Mould - Lamination
Lamination - Assembling

See other bonding pastes



B15F

B15F

Bonding paste flex with fibres


Adhesive bonding paste with high elasticity based on unsaturated polyester resins and reinforced with fibres.
Used in the composite sector for its excellent adhesion for the bonding of laminates and inserts of various types.

SUPPORTS

Fiberglass polyester and vinylester, wood, various types of foam.

GENERAL INSTRUCTIONS FOR USE

Apply on well sanded and cleaned surfaces;
Make sure the substrate is free of dust, fibres, dirt and surface condensation.
Carefully mix the mastic with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required.
The recommended temperature range is between 16 and 28°C.
It must be applied manually with a spatula after careful mixing the hardener or by machine.
For quantities over 5 kg, mixing with a stirrer is recommended, while for 200 l drums, the use of a pressing plate extruder/mixer guarantees the best mixing efficiency.
In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C. Some drift may occur in gel time.


Packaging

Type of use


Mould - Lamination
Lamination - Assembling

See other bonding pastes



SV75

SV75

Vinylester putty for filling with microfibres


White vinylester putty reinforced with con glass microfibres.
Specifically formulated for bubbles, defect and seam filling and surface leveling.
It shows excellent vertical sealing behavior and limited shrinkage even on high thicknesses (up to 4 mm). Suitable for hulls and surfaces directly exposed to the external environment due to its superior performance in terms of thermal, mechanical and anti-osmosis resistance. After sanding it is recommended to smooth with SV70 or SV71 vinylester putty before the following cycles.
Contains Viracolor.

SUPPORTS

Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C


Packaging

Type of use


PLUG
MOULD-LAMINATION
BODY-FINISHING

See other putties



SV71

SV71

Vinylester putty for filling


White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability.
Specifically formulated for filling bubbles, defects and bonded joints, smoothing and manual levelling of surfaces; even on high thicknesses (over 4 mm) it shows excellent vertical sealing behavior and limited shrinkage. Suitable for hulls and surfaces directly exposed to the external environment for its superior thermal, mechanical and anti-osmosis resistance performance. After sanding, it can be painted over with gelcoat; to meet the most demanding finishing specifications, it is advisable to place the vinylester finishing putty for exteriors before the gelcoat (finishing putty SV70).

SUPPORTS

Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
MOULD-LAMINATION
BODY-FINISHING

See other putties



SV70

SV70

Vinylester putty for finishing


White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability, characterized by with superior performance in terms of thermal, mechanical and anti-osmosis resistance. Specifically formulated for marine market for the excellent finishes of surfaces of hull below the water line, and for composite market for the finishing of surfaces directly exposed to climatic agents and external environment. After sanding, it can be painted over with gelcoat. Recommended application in a thin layer (up to a maximum of 4 mm thickness) in bodywork cycles where it is necessary to satisfy the most demanding finishing specifications, directly on the substrate or on top of the putty for filling for exteriors (Putty for filling SV71).

SUPPORTS

Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 4 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
MOULD-LAMINATION
BODY-FINISHING

See other putties



RV8080LP

RV8080LP

Prefilled LP tooling resin vinylester


RV8080LP is a vinylester matrix resin, loaded and pre-accelerated with low styrene content and low profile additive to guarantee shrinkage close to 0.
It is designed for the rapid realization of the laminate with results of excellent surface finishes and high dimensional stability of the moulds.

RV8080LP is specifically indicated for the layering of moulds intended for the production of products by infusion and small molds for RTM; characterized by a linear shrinkage close to 0 and by excellent thermo-mechanical performance.


Packaging

Type of use


MOULD-LAMINATION

See other tooling resins



RS6060LP

RS6060LP

Polyester prefilled LP tooling resin


RS6060LP is an unsaturated polyester-based resin, loaded and pre-accelerated with a low styrene content and low profile additive to guarantee shrinkage close to 0. It is designed for the rapid production of the laminate with excellent surface finish results and high dimensional stability of the moulds.
RS6060LP is particularly suitable for the layering of moulds intended for the production of articles by infusion; characterized by a linear shrinkage close to 0 and by excellent thermo-mechanical performances.


Packaging

Type of use


MOULD-LAMINATION

See other tooling resins



RS2040

RS2040

Prefilled tooling resin for mould HPH


RS2040 is a filled and pre-accelerated unsaturated polyester resin with low styrene content.
RS2040 has been designed for the rapid lamination with results of excellent surface finishes and high dimensional stability of the moulds. Thanks to its high wettability, RS2040 is formulated specifically for manual application or by roller-brush. RS2040 hardens very well at room temperature both with 1 layer of MAT and with 4 or more layers of MAT applied wet on wet. The RS2040 is particularly suitable for the production of large surfaces and also for the production of moulds used in infusion process: characterized by a low exothermic peak, a low volumetric, low linear shrinkage and an high tixotropy that allows to work quickly without dripping, and a low styrene content that allows to operate with low styrene emission, significantly improving the work environment and exposure of the operators.


Packaging

Type of use


PLUG
MOULD-LAMINATION

See other tooling resins



RS2030

RS2030

Prefilled tooling resin HP for mould


RS2030 is a filled and pre-accelerated unsaturated polyester resin with low styrene content.
RS2030 has been designed for the lamination with results of excellent surface finishes and high dimensional stability of the moulds. RS2030 hardens very well at room temperature both with 1 layer of MAT and with 4 or more layers of MAT applied wet on wet. The RS2030 is particularly suitable for the production of large surfaces and also for the production of moulds used in infusion process: characterized by a low exothermic peak, a low volumetric, low linear shrinkage and an high tixotropy that allows to work quickly without dripping, and a low styrene content that allows to operate with low styrene emission, significantly improving the work environment and exposure of the operators.


Packaging

Type of use


PLUG
MOULD-LAMINATION

See other tooling resins