SV75

SV75

Vinylester putty for filling with microfibres


White vinylester putty reinforced with con glass microfibres.
Specifically formulated for bubbles, defect and seam filling and surface leveling.
It shows excellent vertical sealing behavior and limited shrinkage even on high thicknesses (up to 4 mm). Suitable for hulls and surfaces directly exposed to the external environment due to its superior performance in terms of thermal, mechanical and anti-osmosis resistance. After sanding it is recommended to smooth with SV70 or SV71 vinylester putty before the following cycles.
Contains Viracolor.

SUPPORTS

Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C


Packaging

Type of use


PLUG
MOULD-LAMINATION
BODY-FINISHING

See other putties



SV71

SV71

Vinylester putty for filling


White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability.
Specifically formulated for filling bubbles, defects and bonded joints, smoothing and manual levelling of surfaces; even on high thicknesses (over 4 mm) it shows excellent vertical sealing behavior and limited shrinkage. Suitable for hulls and surfaces directly exposed to the external environment for its superior thermal, mechanical and anti-osmosis resistance performance. After sanding, it can be painted over with gelcoat; to meet the most demanding finishing specifications, it is advisable to place the vinylester finishing putty for exteriors before the gelcoat (finishing putty SV70).

SUPPORTS

Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
MOULD-LAMINATION
BODY-FINISHING

See other putties



SV70

SV70

Vinylester putty for finishing


White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability, characterized by with superior performance in terms of thermal, mechanical and anti-osmosis resistance. Specifically formulated for marine market for the excellent finishes of surfaces of hull below the water line, and for composite market for the finishing of surfaces directly exposed to climatic agents and external environment. After sanding, it can be painted over with gelcoat. Recommended application in a thin layer (up to a maximum of 4 mm thickness) in bodywork cycles where it is necessary to satisfy the most demanding finishing specifications, directly on the substrate or on top of the putty for filling for exteriors (Putty for filling SV71).

SUPPORTS

Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 4 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
MOULD-LAMINATION
BODY-FINISHING

See other putties



SG91

SG91

Gel putty for filling


Light white putty-gel specifically formulated for fairing the surfaces to the final shape, used for filling and leveling of counterparts and bulkheads, for filling bubbles, defects and bonded joints, smoothing and manual start-up of large surfaces. Particularly suitable for smoothing over 5 mm and for filling where a gel time of more than 25 minutes is required. The excellent leveling and sandability are accompanied by a low shrinkage and an intense white color that facilitates overpainting with gelcoat, significantly increasing the application yield.
To meet the most demanding finishing specifications, it is advisable to add the finishing putty (SG90) to the gelcoat.

SUPPORTS

Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the product with 1,0 – 2,0% of liquid hardener CT21 (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
BODY-FINISHING

See other putties



SG90

SG90

Gel putty for finishing


White gel putty specifically formulated for the composite sector for the finishing and manual leveling of large surfaces.
The excellent workability and sandability are accompanied by a low shrinkage and an intense white color that facilitates overpainting with gelcoat, significantly increasing the application yield. Recommended in a thin layer in bodywork cycles, directly on the support or on top of the filler putty (SG91 filler putty).

SUPPORTS

Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the product with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
BODY-FINISHING

See other putties



SK41

SK41

Assembling Putty


Polyester putty with glass microfibres for high mechanical resistance filling and smoothing, even of high thickness.
Formulated with high thixotropy and easy spreadability, it is used for the repair, filling and grouting of damaged surfaces, for the assembly of semi-finished and fibreglass products and for the assembling of plug frame and base.

SUPPORTS

Recommended: polyester and vinylester fiberglass laminates.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. On the sheets, eliminate any residual oxide; degrease with antisilicone thinner. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula in one or more layers until the required thickness is reached. Generally recommended dry sanding cycle, grits: P80-P120-P220. In its original packaging, the product can be used for 12 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
FITTING OUT
BODY-FINISHING

See other putties



SK40

SK40

Fibreglass putty


Polyester putty with glass fibres for high mechanical resistance filling and smoothing, even of high thickness. Formulated with high thixotropy and easy spreadability, it is used for the repair, filling and grouting of damaged surfaces, for the assembly of semi-finished and fibreglass products and for the assembling of plug frame and base.

SUPPORTS

Recommended: polyester and vinylester fiberglass laminates.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. On the sheets, eliminate any residual oxide; degrease with antisilicone thinner. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
It must be applied manually with a spatula in one or more layers until the required thickness is reached. Generally recommended dry sanding cycle, grits: P80-P120-P220. In its original packaging, the product can be used for 12 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
FITTING OUT
BODY-FINISHING

See other putties



SK24C

SK24C

Universal soft compact putty


Polyester putty for general use characterized by an exceptional spreadability and sandability. Optimal leveling and deaeration for a complete absence of porosity. Used in the composite sector in the finishing of bonded joints, in the repairing of scratches and small cracks, and in the leveling of the surfaces. Its perfect adhesion to any laminate is combined with low shrinkage and excellent sanding properties.

SUPPORTS

Recommended: polyester and vinylester fiberglass laminates; Raw degreased and sanded metal sheet.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. On the sheets, eliminate any residual oxide; degrease with antisilicone thinner. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
It must be applied manually with a spatula in one or more layers until the required thickness is reached. Generally recommended dry sanding cycle, grits: P80-P120-P220. In its original packaging, the product can be used for 12 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
BODY-FINISHING

See other putties



SK23

SK23

Universal Plus Putty


Polyester putty for general use with low specific weight, characterized by an exceptional spreadability and sandability. Optimal leveling and deaeration for a complete absence of porosity. Used in the composite sector in the plug shaping with standard/hand way, in the finishing of bonded joints, in the repairing of scratches and small cracks, and in the leveling of the surfaces. Its perfect adhesion to any laminate is combined with low shrinkage and excellent sanding properties.

SUPPORTS

Recommended: polyester and vinylester fiberglass laminates; Raw degreased and sanded metal sheet.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. On the sheets, eliminate any residual oxide; degrease with antisilicone thinner. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula in one or more layers until the required thickness is reached. Generally recommended dry sanding cycle, grits: P80-P120-P220. In its original packaging, the product can be used for 12 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
BODY-FINISHING

See other putties



SK21

SK21

Extralight Putty


Lightweight polyester putty applied by spatula.
Used in the composite sector as modeling indicator for the filling of the model and in bodywork for finishing pieces.
Being characterized by soft spreadability and excellent sandability without drying out the sandpaper, it is also appreciated for the finishing of bonded joints, the repairing of scratches and small cracks.
It has shrinkage, it leaves no surface holes.
Its perfect adhesion to any laminate is combined with low shrinkage and excellent sanding properties.

SUPPORTS

Recommended: polyester and vinylester fiberglass laminates; Raw degreased and sanded metal sheet.

GENERAL INSTRUCTIONS FOR USE

Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation.
On the sheets, eliminate any residual oxide; degrease with antisilicone thinner.
Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required.
The recommended temperature range of use is between
12 and 30°C.
It must be applied manually with a spatula in one or more layers until the required thickness is reached.
Generally recommended dry sanding cycle, grits: P80-P120-P220.
In its original packaging, the product can be used for 12 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


PLUG
BODY-FINISHING

See other putties