VHG100B
VHG100B
High gloss paint black
Finishing black paint based on special polyester resins for obtaining surfaces of exceptional quality.
Specifically formulated for the spray finishing of high gloss models.
Easy to apply, once dried it allows to obtain a perfectly workable layer of paint.
SUPPORTS
Recommended: sanded polyester and vinylester bases.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Mix the paint thoroughly. Add 1-2% of MEKP liquid hardener CT21 (methylethyl ketone peroxide), always mixing thoroughly. The product is workable for 15-20 minutes in a cup at 23°C.
Apply by spray up to a maximum thickness of 500 – 600 microns in 4-6 coats of 100-150 microns each. Apply each single coat with 2 or 3 crossed passes, leaving the product to deaerate and spread out for 5 minutes between one coat and the next. Use a gravity spray gun with 1,4 – 1,7 mm nozzle and 2,0 – 2,5 bar (40psi) pressure. Theoretical coverage: 1,0 – 1,2 kg / m2 for 600 microns of thickness. The product can be sanded 12 hours after application at a temperature of 20°C. Typical sanding cycle: P240-P320-P400 by hand and after a further 12 hours complete the sanding cycle with P600-P800-P1200 grits (wet sanding is not recommended) and polish the product. Do not use at temperatures below 16°C. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Note: • To clean the surfaces, do not use silicone cloths or cloths that have been in contact with silicone; • If you want to use a more fluid product, you can proceed, before catalysis, to add 5 – 10% of MEK solvent.
Packaging
lt. 4
Type of use
PLUG
See other High gloss paints
VHG100
VHG100
High gloss paint colorless
Finishing paint based on special polyester resins for obtaining surfaces of exceptional quality.
Specifically formulated for the spray finishing of high gloss models.
Easy to apply, once dried it allows to obtain a perfectly workable layer of paint.
SUPPORTS
Recommended: sanded polyester and vinylester bases.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Mix the paint thoroughly. Add 1-2% of MEKP liquid hardener CT21 (methylethyl ketone peroxide), always mixing thoroughly. The product is workable for 15-20 minutes in a cup at 23°C. Apply by spray up to a maximum thickness of 500 – 600 microns in 4-6 coats of 100-150 microns each. Apply each single coat with 2 or 3 crossed passes, leaving the product to deaerate and spread out for 5 minutes between one coat and the next. Use a gravity spray gun with 1,4 – 1,7 mm nozzle and 2,0 – 2,5 bar (40psi) pressure. Theoretical coverage: 1,0 – 1,2 kg / m2 for 600 microns of thickness.
The product can be sanded 12 hours after application at a temperature of 20°C. Typical sanding cycle: P240-P320-P400 by hand and after a further 12 hours complete the sanding cycle with P600-P800-P1200 grits (wet sanding is not recommended) and polish the product. Do not use at temperatures below 16°C. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Note: • To clean the surfaces, do not use silicone cloths or cloths that have been in contact with silicone; • If you want to use a more fluid product, you can proceed, before catalysis, to add 5 – 10% of MEK solvent.
Packaging
lt. 4
Type of use
PLUG
See other High gloss paints
SV75
SV75
Vinylester putty for filling with microfibres
White vinylester putty reinforced with con glass microfibres.
Specifically formulated for bubbles, defect and seam filling and surface leveling.
It shows excellent vertical sealing behavior and limited shrinkage even on high thicknesses (up to 4 mm). Suitable for hulls and surfaces directly exposed to the external environment due to its superior performance in terms of thermal, mechanical and anti-osmosis resistance. After sanding it is recommended to smooth with SV70 or SV71 vinylester putty before the following cycles.
Contains Viracolor.
SUPPORTS
Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C
Packaging
lt. 4
kg. 25
Type of use
PLUG
MOULD-LAMINATION
BODY-FINISHING
See other Putties
SV71
SV71
Vinylester putty for filling
White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability.
Specifically formulated for filling bubbles, defects and bonded joints, smoothing and manual levelling of surfaces; even on high thicknesses (over 4 mm) it shows excellent vertical sealing behavior and limited shrinkage. Suitable for hulls and surfaces directly exposed to the external environment for its superior thermal, mechanical and anti-osmosis resistance performance. After sanding, it can be painted over with gelcoat; to meet the most demanding finishing specifications, it is advisable to place the vinylester finishing putty for exteriors before the gelcoat (finishing putty SV70).
SUPPORTS
Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
lt. 4
kg. 25
Type of use
PLUG
MOULD-LAMINATION
BODY-FINISHING
See other Putties
SV70
SV70
Vinylester putty for finishing
White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability, characterized by with superior performance in terms of thermal, mechanical and anti-osmosis resistance. Specifically formulated for marine market for the excellent finishes of surfaces of hull below the water line, and for composite market for the finishing of surfaces directly exposed to climatic agents and external environment. After sanding, it can be painted over with gelcoat. Recommended application in a thin layer (up to a maximum of 4 mm thickness) in bodywork cycles where it is necessary to satisfy the most demanding finishing specifications, directly on the substrate or on top of the putty for filling for exteriors (Putty for filling SV71).
SUPPORTS
Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 4 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
lt. 4
kg. 25
Type of use
PLUG
MOULD-LAMINATION
BODY-FINISHING
See other Putties
SG91
SG91
Gel putty for filling
Light white putty-gel specifically formulated for fairing the surfaces to the final shape, used for filling and leveling of counterparts and bulkheads, for filling bubbles, defects and bonded joints, smoothing and manual start-up of large surfaces. Particularly suitable for smoothing over 5 mm and for filling where a gel time of more than 25 minutes is required. The excellent leveling and sandability are accompanied by a low shrinkage and an intense white color that facilitates overpainting with gelcoat, significantly increasing the application yield.
To meet the most demanding finishing specifications, it is advisable to add the finishing putty (SG90) to the gelcoat.
SUPPORTS
Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the product with 1,0 – 2,0% of liquid hardener CT21 (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
kg. 25
Type of use
PLUG
BODY-FINISHING
See other Putties
SG90
SG90
Gel putty for finishing
White gel putty specifically formulated for the composite sector for the finishing and manual leveling of large surfaces.
The excellent workability and sandability are accompanied by a low shrinkage and an intense white color that facilitates overpainting with gelcoat, significantly increasing the application yield. Recommended in a thin layer in bodywork cycles, directly on the support or on top of the filler putty (SG91 filler putty).
SUPPORTS
Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the product with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
lt. 4
kg. 25
Type of use
PLUG
BODY-FINISHING
See other Putties
SK50
SK50
Transparent putty for carbon support
Transparent putty based on special polyester resins.
Excellent spreadability and applicability even vertically. Particularly suitable for transparent grouting, without the occurrence of streaks. The transparency of the grouting remains up to a maximum of 2 mm thick.
SUPPORTS
Carbon.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure that the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener CT21 (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. Once the product has been applied, it is possible to smooth and polish the surface after 6-8 hours. In its original packaging, the product can be used for 12 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
ml. 750
Type of use
PLUG
See other Putties
SK41
SK41
Assembling Putty
Polyester putty with glass microfibres for high mechanical resistance filling and smoothing, even of high thickness.
Formulated with high thixotropy and easy spreadability, it is used for the repair, filling and grouting of damaged surfaces, for the assembly of semi-finished and fibreglass products and for the assembling of plug frame and base.
SUPPORTS
Recommended: polyester and vinylester fiberglass laminates.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. On the sheets, eliminate any residual oxide; degrease with antisilicone thinner. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula in one or more layers until the required thickness is reached. Generally recommended dry sanding cycle, grits: P80-P120-P220. In its original packaging, the product can be used for 12 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
ml. 750
lt. 4
kg. 25
Type of use
PLUG
FITTING OUT
BODY-FINISHING
See other Putties
SK40
SK40
Fibreglass putty
Polyester putty with glass fibres for high mechanical resistance filling and smoothing, even of high thickness. Formulated with high thixotropy and easy spreadability, it is used for the repair, filling and grouting of damaged surfaces, for the assembly of semi-finished and fibreglass products and for the assembling of plug frame and base.
SUPPORTS
Recommended: polyester and vinylester fiberglass laminates.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. On the sheets, eliminate any residual oxide; degrease with antisilicone thinner. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
It must be applied manually with a spatula in one or more layers until the required thickness is reached. Generally recommended dry sanding cycle, grits: P80-P120-P220. In its original packaging, the product can be used for 12 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
ml. 750
lt. 4