SV75
SV75
Vinylester putty for filling with microfibres
White vinylester putty reinforced with con glass microfibres.
Specifically formulated for bubbles, defect and seam filling and surface leveling.
It shows excellent vertical sealing behavior and limited shrinkage even on high thicknesses (up to 4 mm). Suitable for hulls and surfaces directly exposed to the external environment due to its superior performance in terms of thermal, mechanical and anti-osmosis resistance. After sanding it is recommended to smooth with SV70 or SV71 vinylester putty before the following cycles.
Contains Viracolor.
SUPPORTS
Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C
Packaging
lt. 4
kg. 25
Type of use
PLUG
MOULD-LAMINATION
BODY-FINISHING
See other Putties
SV71
SV71
Vinylester putty for filling
White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability.
Specifically formulated for filling bubbles, defects and bonded joints, smoothing and manual levelling of surfaces; even on high thicknesses (over 4 mm) it shows excellent vertical sealing behavior and limited shrinkage. Suitable for hulls and surfaces directly exposed to the external environment for its superior thermal, mechanical and anti-osmosis resistance performance. After sanding, it can be painted over with gelcoat; to meet the most demanding finishing specifications, it is advisable to place the vinylester finishing putty for exteriors before the gelcoat (finishing putty SV70).
SUPPORTS
Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
lt. 4
kg. 25
Type of use
PLUG
MOULD-LAMINATION
BODY-FINISHING
See other Putties
SV70
SV70
Vinylester putty for finishing
White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability, characterized by with superior performance in terms of thermal, mechanical and anti-osmosis resistance. Specifically formulated for marine market for the excellent finishes of surfaces of hull below the water line, and for composite market for the finishing of surfaces directly exposed to climatic agents and external environment. After sanding, it can be painted over with gelcoat. Recommended application in a thin layer (up to a maximum of 4 mm thickness) in bodywork cycles where it is necessary to satisfy the most demanding finishing specifications, directly on the substrate or on top of the putty for filling for exteriors (Putty for filling SV71).
SUPPORTS
Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.
GENERAL INSTRUCTIONS FOR USE
Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 4 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
lt. 4
kg. 25
Type of use
PLUG
MOULD-LAMINATION
BODY-FINISHING
See other Putties
RV8080LP
RV8080LP
Prefilled LP tooling resin vinylester
RV8080LP is a vinylester matrix resin, loaded and pre-accelerated with low styrene content and low profile additive to guarantee shrinkage close to 0.
It is designed for the rapid realization of the laminate with results of excellent surface finishes and high dimensional stability of the moulds.
RV8080LP is specifically indicated for the layering of moulds intended for the production of products by infusion and small molds for RTM; characterized by a linear shrinkage close to 0 and by excellent thermo-mechanical performance.
Packaging
kg. 250
Type of use
MOULD-LAMINATION
See other Tooling resins
RS6060LP
RS6060LP
Polyester prefilled LP tooling resin
RS6060LP is an unsaturated polyester-based resin, loaded and pre-accelerated with a low styrene content and low profile additive to guarantee shrinkage close to 0. It is designed for the rapid production of the laminate with excellent surface finish results and high dimensional stability of the moulds.
RS6060LP is particularly suitable for the layering of moulds intended for the production of articles by infusion; characterized by a linear shrinkage close to 0 and by excellent thermo-mechanical performances.
Packaging
kg. 25
kg. 250
kg. 1000
Type of use
MOULD-LAMINATION
See other Tooling resins
RS2040
RS2040
Prefilled tooling resin for mould HPH
RS2040 is a filled and pre-accelerated unsaturated polyester resin with low styrene content.
RS2040 has been designed for the rapid lamination with results of excellent surface finishes and high dimensional stability of the moulds. Thanks to its high wettability, RS2040 is formulated specifically for manual application or by roller-brush. RS2040 hardens very well at room temperature both with 1 layer of MAT and with 4 or more layers of MAT applied wet on wet. The RS2040 is particularly suitable for the production of large surfaces and also for the production of moulds used in infusion process: characterized by a low exothermic peak, a low volumetric, low linear shrinkage and an high tixotropy that allows to work quickly without dripping, and a low styrene content that allows to operate with low styrene emission, significantly improving the work environment and exposure of the operators.
Packaging
kg. 25
kg. 250
kg. 1000
Type of use
PLUG
MOULD-LAMINATION
See other Tooling resins
RS2030
RS2030
Prefilled tooling resin HP for mould
RS2030 is a filled and pre-accelerated unsaturated polyester resin with low styrene content.
RS2030 has been designed for the lamination with results of excellent surface finishes and high dimensional stability of the moulds. RS2030 hardens very well at room temperature both with 1 layer of MAT and with 4 or more layers of MAT applied wet on wet. The RS2030 is particularly suitable for the production of large surfaces and also for the production of moulds used in infusion process: characterized by a low exothermic peak, a low volumetric, low linear shrinkage and an high tixotropy that allows to work quickly without dripping, and a low styrene content that allows to operate with low styrene emission, significantly improving the work environment and exposure of the operators.
Packaging
kg. 250
kg. 1000
Type of use
PLUG
MOULD-LAMINATION
See other Tooling resins
RV2015R / RV2015S
RV2015R / RV2015S
Vinylester resin for skincoat rapid / slow
RV2015R is a pre-accelerated, thixotropic vinylester resin to be used as a thin layer, in the creation of the mould or other composite parts.
and heat resistance necessary for the realization of a durable mold that requires reduced maintenance, increase the resistance to breakage of the gelcoat caused by flexing and impact of the laminate, increase the resistance to osmosis, and allows to obtain composite parts with excellent hardness.
When high thermo-mechanical properties are required in the finished product, it can also be used as a resin in the entire lamination process.
GENERAL INSTRUCTIONS FOR USE
RV2015 can be applied by manual or spray lamination. Catalysis 1,0% – 2,0% of the total weight of the resin with CT21 hardener (Methylethylketone Peroxide / Butanox M50). The best results are obtained by working at temperatures between 18°C and 30°C and with a relative humidity rate between 40% and 90%. It is recommended to maintain constant application conditions in order to have constant viscosity and gel times. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
Packaging
kg. 20
kg. 220
kg. 1000
Type of use
PLUG
MOULD-LAMINATION
See other Tooling resins
L80
L80
Universal polish
Indirect multi-emulsions of essential oils, wetting and filming oils for cosmetological use, biodegradable in the aqueous phase.
Contains a vegetable thixotropic that favors the uniformity of the film. It has exceptional cleaning, polishing and brightening power, gives uniformity to the treated surfaces and has a protective effect against smog. On glass and transparent surfaces, it does not leave iridescence.
GENERAL INSTRUCTIONS FOR USE
Apply the product by hand or by machine with special pads or soft rags. Allow the product to dry and remove the residue formed with clean rags or pads. 100 g. of product are sufficient to polish 3/4 square meters of surface. Dilution with water is recommended, particularly in summer.
SOLUBILITY: unlimited in water.
Packaging
lt. 1
Type of use
PLUG
MOULD-LAMINATION
BODY-FINISHING
See other Polishing products
L71
L71
Extra mordant abrasive paste
Extra-mordant abrasive paste based on emulsifiers and special abrasives, suitable for polishing gelcoat, finished products and molds. Its special formulation with high grinding power allows the rapid polishing of surfaces with high hardness and the removal of marks and scratches of medium depth.
GENERAL INSTRUCTIONS FOR USE
Ready to use product. If necessary, dilute with water or solvent (naphtha, petroleum). Thoroughly clean the surface to be treated and make sure it is free of grease and foreign substances. Spread the paste evenly over the entire surface, making sure the surface is cold.
Use with a polisher at a speed between 1000 – 1500 rpm and with special pads.
Avoid overheating the gelcoat by operating for too long on the same area. At the end of polishing, remove any paste residues with clean rags or pads. To obtain greater brilliance, complete the polishing with Polish L80. In its original packaging, the product can be used for 2 years if stored indoor away from direct sunlight and away from heat sources.
Packaging
