G42

G42

Bonding paste smooth without fibres


Adhesive bonding paste viracolor made from unsaturated polyester resins and mineral fibres.
Used in the composite sector for samm angles and chines smoothing, gluing of inserts and core materials.

SUPPORTS

Recommended: Gelcoat, polyester and vinylester fibreglass, wood, various types of foam.

GENERAL INSTRUCTIONS FOR USE

Apply on well sanded and cleaned surfaces;
Make sure the substrate is free of dust, fibres, dirt and surface condensation.
Carefully mix the bonding paste with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required.
The recommended temperature range is between 16 and 28°C. The product contains viracolor.
It must be applied manually with a spatula after careful mixing the hardener or by machine.
For quantities over 5 kg mixing with a stirrer is recommended; for 200 l drums, the use of a pressing plate extruder-mixer guarantees the best mixing efficiency.
In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


Mould - Lamination
Lamination - Assembling

See other Bonding Pastes



G32

G32

Bonding paste smooth with fibres


Adhesive bonding paste viracolor made from unsaturated polyester resins, reinforced with mineral fibres.
Used in the composite sector for its excellent adhesion in bonding laminates and inserts of various types.
The reinforcing fibers give this product high mechanical resistance, making it suitable for bonding floors and cielings, filling of the strips and gluing inserts.

SUPPORTS

Recommended: polyester and vinylester fibreglass, wood, various types of foam.

GENERAL INSTRUCTIONS FOR USE

Apply on well sanded and cleaned surfaces;
Make sure the substrate is free of dust, fibres, dirt and surface condensation.
Carefully mix the bonding paste with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required.
The recommended temperature range is between 16 and 28°C. The product contains viracolor.
It must be applied manually with a spatula after careful mixing the hardener or by machine.
For quantities over 5 kg mixing with a stirrer is recommended; for 200 l drums, the use of a pressing plate extruder-mixer guarantees the best mixing efficiency.
In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


Packaging

Type of use


Mould - Lamination
Lamination - Assembling

See other Bonding Pastes



B15F

B15F

Bonding paste flex with fibres


Adhesive bonding paste with high elasticity based on unsaturated polyester resins and reinforced with fibres.
Used in the composite sector for its excellent adhesion for the bonding of laminates and inserts of various types.

SUPPORTS

Fiberglass polyester and vinylester, wood, various types of foam.

GENERAL INSTRUCTIONS FOR USE

Apply on well sanded and cleaned surfaces;
Make sure the substrate is free of dust, fibres, dirt and surface condensation.
Carefully mix the mastic with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the amount of hardener required depends on the temperature of use and the processing times required.
The recommended temperature range is between 16 and 28°C.
It must be applied manually with a spatula after careful mixing the hardener or by machine.
For quantities over 5 kg, mixing with a stirrer is recommended, while for 200 l drums, the use of a pressing plate extruder/mixer guarantees the best mixing efficiency.
In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C. Some drift may occur in gel time.


Packaging

Type of use


Mould - Lamination
Lamination - Assembling

See other Bonding Pastes



Request information Tooling Pastes

Tooling Pastes

Request technical documentation

Fill out the form

Write in the body of the message for which products you wish to receive technical documentation



    I WANT TO SUBSCRIBE TO THE NEWSLETTER
    I have read the Privacy Policy and accept the use of my personal data. Intec Srl will use the data entered to send communications regarding the services offered and personalized news, containing material and promotional initiatives of its activities and services using traditional (email) or automated (newsletter) methods.


    Intec Srl will use such data only and exclusively to respond to the request for information received. Intec Srl will keep the data for the period necessary to carry out the requested service, in any case the user can request its cancellation at any time.


    VHG100B

    VHG100B

    High gloss paint black


    Finishing black paint based on special polyester resins for obtaining surfaces of exceptional quality.
    Specifically formulated for the spray finishing of high gloss models.
    Easy to apply, once dried it allows to obtain a perfectly workable layer of paint.

    SUPPORTS

    Recommended: sanded polyester and vinylester bases.

    GENERAL INSTRUCTIONS FOR USE

    Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Mix the paint thoroughly. Add 1-2% of MEKP liquid hardener CT21 (methylethyl ketone peroxide), always mixing thoroughly. The product is workable for 15-20 minutes in a cup at 23°C.
    Apply by spray up to a maximum thickness of 500 – 600 microns in 4-6 coats of 100-150 microns each. Apply each single coat with 2 or 3 crossed passes, leaving the product to deaerate and spread out for 5 minutes between one coat and the next. Use a gravity spray gun with 1,4 – 1,7 mm nozzle and 2,0 – 2,5 bar (40psi) pressure. Theoretical coverage: 1,0 – 1,2 kg / m2 for 600 microns of thickness. The product can be sanded 12 hours after application at a temperature of 20°C. Typical sanding cycle: P240-P320-P400 by hand and after a further 12 hours complete the sanding cycle with P600-P800-P1200 grits (wet sanding is not recommended) and polish the product. Do not use at temperatures below 16°C. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
    Note: • To clean the surfaces, do not use silicone cloths or cloths that have been in contact with silicone; • If you want to use a more fluid product, you can proceed, before catalysis, to add 5 – 10% of MEK solvent.


    Packaging

    Type of use


    PLUG

    See other High gloss paints



    VHG100

    VHG100

    High gloss paint colorless


    Finishing paint based on special polyester resins for obtaining surfaces of exceptional quality.
    Specifically formulated for the spray finishing of high gloss models.
    Easy to apply, once dried it allows to obtain a perfectly workable layer of paint.

    SUPPORTS

    Recommended: sanded polyester and vinylester bases.

    GENERAL INSTRUCTIONS FOR USE

    Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Mix the paint thoroughly. Add 1-2% of MEKP liquid hardener CT21 (methylethyl ketone peroxide), always mixing thoroughly. The product is workable for 15-20 minutes in a cup at 23°C. Apply by spray up to a maximum thickness of 500 – 600 microns in 4-6 coats of 100-150 microns each. Apply each single coat with 2 or 3 crossed passes, leaving the product to deaerate and spread out for 5 minutes between one coat and the next. Use a gravity spray gun with 1,4 – 1,7 mm nozzle and 2,0 – 2,5 bar (40psi) pressure. Theoretical coverage: 1,0 – 1,2 kg / m2 for 600 microns of thickness.
    The product can be sanded 12 hours after application at a temperature of 20°C. Typical sanding cycle: P240-P320-P400 by hand and after a further 12 hours complete the sanding cycle with P600-P800-P1200 grits (wet sanding is not recommended) and polish the product. Do not use at temperatures below 16°C. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.
    Note: • To clean the surfaces, do not use silicone cloths or cloths that have been in contact with silicone; • If you want to use a more fluid product, you can proceed, before catalysis, to add 5 – 10% of MEK solvent.


    Packaging

    Type of use


    PLUG

    See other High gloss paints



    SV75

    SV75

    Vinylester putty for filling with microfibres


    White vinylester putty reinforced with con glass microfibres.
    Specifically formulated for bubbles, defect and seam filling and surface leveling.
    It shows excellent vertical sealing behavior and limited shrinkage even on high thicknesses (up to 4 mm). Suitable for hulls and surfaces directly exposed to the external environment due to its superior performance in terms of thermal, mechanical and anti-osmosis resistance. After sanding it is recommended to smooth with SV70 or SV71 vinylester putty before the following cycles.
    Contains Viracolor.

    SUPPORTS

    Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

    GENERAL INSTRUCTIONS FOR USE

    Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C


    Packaging

    Type of use


    PLUG
    MOULD-LAMINATION
    BODY-FINISHING

    See other Putties



    SV71

    SV71

    Vinylester putty for filling


    White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability.
    Specifically formulated for filling bubbles, defects and bonded joints, smoothing and manual levelling of surfaces; even on high thicknesses (over 4 mm) it shows excellent vertical sealing behavior and limited shrinkage. Suitable for hulls and surfaces directly exposed to the external environment for its superior thermal, mechanical and anti-osmosis resistance performance. After sanding, it can be painted over with gelcoat; to meet the most demanding finishing specifications, it is advisable to place the vinylester finishing putty for exteriors before the gelcoat (finishing putty SV70).

    SUPPORTS

    Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

    GENERAL INSTRUCTIONS FOR USE

    Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 2,0% of liquid hardener (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


    Packaging

    Type of use


    PLUG
    MOULD-LAMINATION
    BODY-FINISHING

    See other Putties



    SV70

    SV70

    Vinylester putty for finishing


    White vinylester putty based on extra-fine mineral fillers that give the product excellent spreadability and sandability, characterized by with superior performance in terms of thermal, mechanical and anti-osmosis resistance. Specifically formulated for marine market for the excellent finishes of surfaces of hull below the water line, and for composite market for the finishing of surfaces directly exposed to climatic agents and external environment. After sanding, it can be painted over with gelcoat. Recommended application in a thin layer (up to a maximum of 4 mm thickness) in bodywork cycles where it is necessary to satisfy the most demanding finishing specifications, directly on the substrate or on top of the putty for filling for exteriors (Putty for filling SV71).

    SUPPORTS

    Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

    GENERAL INSTRUCTIONS FOR USE

    Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the putty with 1,0 – 3,0% of hardener in paste (benzoyl peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C.
    It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 4 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


    Packaging

    Type of use


    PLUG
    MOULD-LAMINATION
    BODY-FINISHING

    See other Putties



    SG91

    SG91

    Gel putty for filling


    Light white putty-gel specifically formulated for fairing the surfaces to the final shape, used for filling and leveling of counterparts and bulkheads, for filling bubbles, defects and bonded joints, smoothing and manual start-up of large surfaces. Particularly suitable for smoothing over 5 mm and for filling where a gel time of more than 25 minutes is required. The excellent leveling and sandability are accompanied by a low shrinkage and an intense white color that facilitates overpainting with gelcoat, significantly increasing the application yield.
    To meet the most demanding finishing specifications, it is advisable to add the finishing putty (SG90) to the gelcoat.

    SUPPORTS

    Recommended: fiberglass laminates, fillers and polyester and vinylester mastics.

    GENERAL INSTRUCTIONS FOR USE

    Apply on well cleaned sanded surfaces; make sure the substrate is free of dust, fibers, dirt and surface condensation. Carefully mix the product with 1,0 – 2,0% of liquid hardener CT21 (methylethyl ketone peroxide), bearing in mind that the quantity of required hardener, depends on the temperature of use and the processing times required. The recommended temperature range of use is between 12 and 30°C. It must be applied manually with a spatula. For further and more specific application details on the putty finishing cycles, refer to “Guidelines for the finishing of the hull”, available at INTEC’s Technical Assistance Center. In its original packaging, the product can be used for 6 months if stored indoor away from direct sunlight, at temperatures not exceeding 20°C.


    Packaging

    Type of use


    PLUG
    BODY-FINISHING

    See other Putties